Rubber Roof Replacement in Dundee from $5. EPDM at $5 to $9 a square foot -- what people mean by a rubber roof, and when it is the right one. Free inspection and a written quote.
At mill scale black EPDM starts to give ground. A very large dark roof over occupied space absorbs a great deal of heat, and that is where TPO at $6 to $12 earns its premium. On an unheated warehouse roof the argument mostly disappears again.
When people here say rubber roof they almost always mean EPDM, and it installs at $5 to $9 per square foot. It is the least expensive of the single-ply systems, it handles a freezing winter well, and on a small to medium roof it is frequently the correct choice rather than merely the cheap one.



Rubber roof means EPDM here, and it installs at $5 to $9 per square foot -- the least expensive single-ply, and on a small to medium roof frequently the correct choice rather than a compromise. What has to be in the quote is the thickness and the attachment method, because 'rubber roof' on its own is not a specification. Priced per square foot rather than as a building, because the roofs here are mill-scale. What moves it is the plant on top and whether production below can continue -- and exposure by the water, which puts perimeter fixing on the list.
A 45-mil fully adhered membrane is not the same purchase as a 60-mil mechanically fastened one. On a roof you intend to keep, 60-mil is a small uplift for real durability. Over a trading shop, fully adhered avoids the noise and vibration that fastening puts through the ceiling.
Reflectivity on a large dark roof over occupied space, and seams: EPDM is bonded with adhesive and tape rather than welded, so on a roof with many penetrations the workmanship at each one is doing more of the work. TPO at $6 to $12 is the alternative.
On a twelve-by-fifteen extension the difference between systems is far less than the difference between good and careless detailing. We would rather spend the money on the junction with the pitched roof above it.
Dundee is where the large-area low-slope roofs are. A mill-era building carries a roof measured in tens of thousands of square feet with plant, curbs and ducting on it, and on those the membrane is the smaller half of the cost. Exposure by the water is the other factor: perimeter fixing matters more here than inland.
Two things move a Passaic price more than the covering does, and both are consequences of density rather than of roofing.
At 22,514 people per square mile the answer is rarely simple. No side yard, usually no driveway, and a dumpster that has to go on the street with an arrangement. Material up the frontage and waste down it is labor, and a quote that does not mention it has either absorbed it or not thought about it.
An attached building has no eaves. Water leaves through an internal outlet or a scupper cut through a parapet wall, so the failures are at the coping, the upstand and the outlet. A roof quote covering the field and silent on those has priced the easy part.
A blocked outlet ponds the roof instead of overflowing off an edge. Water standing in a lap through a cold week expands and lifts it, then thaws and runs in through the gap it just made. Outlet capacity is the cheapest genuine upgrade on a roof here.
Scale changes the arithmetic by the river.
Large-area low slope is the whole job by the river, and at that scale the insulation specification and the attachment method matter as much as the membrane.
Very little shingle by the river -- the workers' housing that has it is the exception among industrial buildings.
Converted mill buildings are the interesting case by the river: residential units under an industrial-scale roof, frequently with original structure and later plant on top.
This is the genuine commercial roofing in the city: mill-era buildings with roofs measured in tens of thousands of square feet, plant on them and production underneath that cannot stop.
No side yard, no driveway, parapets on every side.
Semi-detached and pitched. Eaves are back in play.
The tightest frontages, and party-wall junctions.
The shop below decides the hours and the route.
Bus routes and loading bays. Arrange the street first.
A more open grid, so a dumpster needs no negotiation.
Detached houses, side access, sometimes no permit.
The questions that decide this job, answered up front.
On a roof you intend to keep, 60-mil. The uplift on a small roof is modest and it buys real puncture resistance and durability. On a small rear addition you expect to rebuild within a decade, 45-mil fully adhered is entirely adequate and we will say so.
With mechanical fastening, yes -- it is screws through the deck. Fully adhered avoids that, which matters over a trading shop or a bedroom. It is worth raising before the system is chosen rather than after the first complaint.
At an edge, almost certainly. An attached building has no eaves, so water leaves through an internal outlet or a scupper through the parapet -- and the failures are at the coping on top of the wall, at the upstand where the membrane turns up it, or at the outlet itself. The field is usually the last thing wrong with a roof here.
Rubber means EPDM, at $5 to $9 per square foot: bonded with adhesive and tape, black, and the least expensive single-ply. TPO is $6 to $12, welded at the seams and reflective, which matters on a large roof over occupied space. On a small rear addition EPDM is usually the right answer rather than the cheap one.
Two to five days on a house, four to seven on an apartment building, and one to three weeks on real commercial work. The roofing is rarely the long part: the street arrangement, the route onto the roof and any tenant notice periods are what set the start date in this city.
The route to the roof established before anything is priced. New Jersey figures, with the access stated rather than buried.